Plastic Storage Box Mold

Plastic Storage Box Mold

Plastic Storage Box Mold of Jiutai JMJT Mold Company
Plastic storage boxes usually feature large volume, complex structure, uneven wall thickness, etc. The core design points are as follows:

  • Fast Delievery
  • Quality Assurance
  • 24/7 Customer Service
Product Introduction

1. Cavity and Parting Surface Design: Adapting to the Structure of Storage Boxes

  • Number of Cavities: Choose "single-cavity mold" or "multi-cavity mold" according to production needs:
  • Single-cavity mold: Suitable for customized and large-sized storage boxes (such as wardrobe storage boxes with length and width exceeding 50cm). Its advantages are simple mold structure and convenient debugging, while the disadvantage is low production efficiency.
  • Multi-cavity mold: Suitable for small and medium-sized storage boxes, with common designs of 2 cavities and 4 cavities. It is necessary to ensure uniform material feeding in each cavity to avoid dimensional differences of products in different cavities.
  • Selection of Parting Surface: Priority should be given to positions on the storage box that "have no appearance requirements" or are "hidden" (such as the bottom and the inner side of the buckle) to prevent the parting line from affecting the appearance. If the storage box has a cover, it is necessary to design the "box body mold" and "box cover mold" simultaneously, and ensure the fitting gap between them (usually 0.1-0.2mm) to avoid the cover being loose or too tight when buckled.

 

product-503-479

 

2. Wall Thickness and Reinforcing Rib Design: Preventing Product Deformation

  • Plastic storage boxes need to balance "lightweight" and "load-bearing capacity", so mold design must control the uniformity of wall thickness:
  • Wall Thickness Control: The wall thickness of conventional storage boxes is recommended to be 1.5-3mm (adjusted according to size; larger sizes require thicker walls). The mold cavity must strictly correspond to the wall thickness to avoid "sink marks" caused by local excessive thickness (such as the connection between the box wall and the handle) or "material shortage" caused by local insufficient thickness (such as the corner positions).
  • Reinforcing Rib Optimization: Design reinforcing ribs on the side walls and bottom of the storage box (height ≤ 3 times the wall thickness, width ≈ 0.5-0.8 times the wall thickness). The mold must process the rib cavity synchronously, and a fillet of R0.5-R1mm should be made at the transition between the reinforcing rib and the box wall to reduce stress concentration and prevent product brittleness and cracking.

product-522-396

 

3. Demolding System Design: Ensuring Smooth Part Removal

  • Due to the large volume of the storage box and the possible presence of undercut structures such as buckles, the demolding system is a key part of the design:
  • Ejection Mechanism: Priority is given to the combined ejection of "ejector pins + ejection plates" (the large-area ejection plate lifts the bottom of the box, and the small ejector pins lift the buckles/handles) to avoid product deformation caused by single-point ejection. If the inner wall of the storage box is smooth, "ejector sleeves" (sleeved on the core) can be added to improve the ejection stability.
  • Undercut Handling: If the storage box has buckles (such as the positioning buckles of stackable storage boxes), the mold must be designed with a "core-pulling mechanism" (such as inclined guide pillar core-pulling, hydraulic core-pulling). After molding, the undercut core is pulled out first, and then the product is ejected to prevent the buckles from being broken.

product-512-473

 

4. Cooling System Design: Improving Production Efficiency and Precision

The storage box has a large volume, and uneven cooling is likely to cause shrinkage and deformation, so the mold cooling system must cover all areas:

  • Cooling Water Channel Layout: Arrange cooling water channels (diameter 8-12mm) evenly along the side walls and bottom of the cavity. The distance between the water channels and the cavity surface should be ≥ 15mm, and interference with the ejector pins and core-pulling mechanism should be avoided. For thick-walled parts such as handles and reinforcing ribs, "water baffles" or "jet cooling" should be added to accelerate local cooling.
  • Cooling Medium: Circulating cooling water (water temperature 20-30℃) is used. If crystalline plastics such as PP and PE are produced, the water temperature can be appropriately reduced (15-20℃) to reduce the product shrinkage rate. The cooling time usually accounts for 50%-70% of the injection molding cycle. With reasonable design, the cycle can be shortened from 60 seconds to less than 40 seconds.

 

 

Hot Tags: plastic storage box mold, China plastic storage box mold manufacturers, factory, packaging injection mold, injection mold assembly, injection mold capacity, plastic injection mould supplier, household appliance injection mould, injection mold heating system

You Might Also Like

(0/10)

clearall